Home  |  Contact Us  |  Quality Statement  |  News
OCM Menufacturing - Manufacturing for today's emerging brands

Corporate Industries Our Services Resource Centre
Chinese Microsite
 Francais

Resource Centre




Related Photos



Shown: Natural bridge versus proper routing (click to enlarge)


Shown: Example of "tombstoning" due to thermal imbalance (click to enlarge)


Shown: PCB with outside border for clearance (click to enlarge)

DFM Tips

Best Practices for Surface Mount Technology (SMT) Design

Increasingly fine-pitch devices and increasing levels of automation are resulting in greater density in board design than ever before. But, there are mechanical and logistical limits to how far these trends can continue, and the following best practices will help ensure that an SMT device is manufacturable.

Natural Bridges
On fine-pitch devices, designers must be careful to ensure that no natural bridges occur. A natural bridge is a clear, straight track between leads. This creates a trace over which solder can (and likely will) run when soldered. Although the result is not technically a defect, it appears as one to both automated and human testers. This causes delays and additional manual (i.e. costly) intervention to check.

To avoid natural bridges, tracks should be designed to route from the ends of pads rather than using direct, straight connections.

Vias & BGAs
Vias are holes drilled through layers of a PCB and plated to connect the layers of circuitry. Two design best practices should be observed regarding vias and ball grid arrays (BGA):

  • Always mask vias that occur under BGAs. There is always a chance that solder from the paste or balls on the BGA may come into contact with the via, creating a defect. Rework of such defects is problematic as more heat is required to melt the solder. To avoid this situation, mask vias under BGAs with solder resist.
  • Avoid placing vias in pads. If a via placed where a device is to be mounted, solder can run down the via, making rework difficult and reducing control over the solder joint volume.
  • Always ensure that copper pads define the solderable area rather than using mask-defined pads. The mask application process is not as well controlled as the copper definition process and defects are more likely to result.

    Thermal Balance
    Balance the thermal mass on leads of smaller devices, especially 0402. Thermal imbalances can cause a defect known as “tombstoning” – as one end of the device reaches temperature faster than the other end, surface tension on the molten lead causes the device to stand up on end.

    Plating
    It is important to achieve a flat PCB finish, so organic surface protection (OSP) material, electroless gold plating, or immersion tin finishes should be used on fine-pitch and BGA devices. This helps to prevent defects such as open circuits on devices that contain many coplanar leads.

    Damming
    Solder resist dams of .003 inches are required, particularly on fine-pitch SMT devices. Omitting these dams increases the risk of short circuits through bridging between leads. The dams between these leads must be a minimum of .003 inches in order to be manufacturable by modern PCB fabrication processes.

    Wave Solder Considerations
    The most economical method of soldering PTH on SMT boards is with a solder wave machine (rather than manually). To help ensure that a board can be successfully passed through the wave, the following best practices should be observed.

    Weight
    Problems in manufacturing arise when a mixed board is heavy. Proper support and clear edges for stiffeenrs helps avoid such issues.

    “Submarining” is the term used to describe the difficulties encountered when a double-sided board with inadequate support is put through wave solder. The board may sag, allowing solder to run across the top of the board and ruin it.

    Clearance
    If a double-sided mixed-technology board is so dense that the above guidelines cannot be observed, a special fixture called a selective wave fixture into which the board is snapped can be used. This masks the bottom-side surface mount from the wave. To do this, there must be sufficient clearance (0.1 inch) between the PTH pins and solder-side SMT so that the SMT can be masked by the fixture.

    Keep in mind that fixtures add cost to the product and so it is best to avoid designs that require these. At several hundreds of dollars per fixture, several fixtures are required, and they have to be cleaned, loaded, unloaded, and occasionally replaced. All of this increases costs.

    Padding
    Careful SMT pad design should be employed on the solder-side of a board. This includes thieving pads and toe pads, both necessary for successful wave soldering. In addition, components on the board should be oriented so that the solder joints are not shadowed as the board moves through the wave solder.

    Techniques for Dense SMT Design
    In all designs, snap-off materials should be designed on the edges of the board. These help support the board through the wave machine and can be removed after soldering. They also allow for the proper function of conveying and clamping systems.

    In some cases, titanium stiffeners can be used (provided there are sufficient clear areas on the board) to help make the board more rigid.

    Both of these techniques require additional labour and therefore add cost to the final product.

    At OCM Manufacturing, we can work with designers to ensure that their plans and prototypes are manufacturable and therefore marketable. Contact one of our Program Managers for details about how we can help.

    		•